Reeds 'n Stuff/Bassoon/Reed Making Machines/Accessories and Blades/Tip Profiling products

Transport Bag 89.10 €

Thu, 30 Apr 2026 13:16:03 +0200

Tip Profiler To Go

The Reeds 'n Stuff transport case features a simple design that's easy to use. The foam interior allows a safe transport and provides a snug fit. The tools to use the machine can be stored in the zipper closed compartment on top of the case. The handle gives Portability wherever you need it.

Blade 360° 179.00 €

Sat, 02 May 2026 11:56:14 +0200

A Revolution into the Future

After years of development, Reeds 'n Stuff is proud to offer the Blade 360°. When the blade becomes dull simply rotate to the next sharp section and continue profiling. This can be done at least 6 times, providing reeds and reeds of profiling before a replacement blade is needed.

The screw holding the blade is easily accessed from the underside, meaning once the height of the blade holder is set, you can set it and forget it. Simply loosen the screw, rotate the blade, and re-tighten the screw. Within seconds you can continue profiling reeds, rather than having to replace the entire blade.

To rotate the blade, first loosen the screw on the underside of the blade holder with the attached screwdriver.

Carefully rotate the blade to the next desired position.

Hold the blade in place while tightening the screw with the provided screwdriver and you are ready to profile.

Note: be sure not to over-tighten the screw holding the blade. Due to its small size it is possible to damage the screw and/or screwdriver in this manner.

FAQ 360° Blade

Spare Blade 97.90 €

Sat, 02 May 2026 00:49:00 +0200

A Revolution into the Future

To rotate the blade, first loosen the screw on the underside of the blade holder with the attached screwdriver.

Carefully rotate the blade to the next desired position.

Hold the blade in place while tightening the screw with the provided screwdriver and you are ready to profile.

Note: be sure not to over-tighten the screw holding the blade. Due to its small size it is possible to damage the screw and/or screwdriver in this manner.

FAQ 360° Blade

Spare Blade (till 2012) 107.43 €

Thu, 30 Apr 2026 13:16:03 +0200

for Tip Profiler

Blade Adjustment Indicator 210.04 €

Thu, 30 Apr 2026 13:15:38 +0200

Dial it in

Simply adjust the blade of your Profiling Machine with our new Blade Adjustment Indicator.

52 Clock Face

54 Srew

57 Measuring Pin

24 Blade Set Screw

25 Blade Adjustment Srew

Before you begin, remove both the wooden handle and the blade. Then fit the dial indicator over the carriage as pictured.

Tighten the large screw on the dial indicator to secure it.

Rotate the clock face as needed to set the dial indicator to zero.

Place the blade on the carriage as pictured. As you slide the blade into place, the slot the side should fit with the corresponding ledge on Screw #25. At this point it is important to confirm that the blade does not protrude beyond the black depth stop.

Tighten Screw #24 all the way, so that the blade is held completely in place. Then gently loosen it by less than a quarter of a turn, until the blade is held securely but can be moved by turning Screw #25.

Turn Screw #25 until the dial indicator reads precisely 2.5 to 3 hundredths of a mm (=0.025-0.03 mm) . At this point, the blade depth will be set appropriately.

Tighten screw #24 all the way. The machine is now ready to use. Before you start using the machine make sure the blade does not touch the tongue. See instructions in chapter: thickness adjustment.

As you remove the dial indicator from the carriage, be sure to pull on the axle of the dial indicator as shown to avoid any damaging contact with the blade.

Contra Exchange Set 313.22 €

Fri, 01 May 2026 22:22:12 +0200

For changing your bassoon tip profiler into a contra bassoon profiler.

Tongue 178.50 €

Thu, 30 Apr 2026 07:29:39 +0200

for Tip Profiler

Mandrel 51.42 €

Fri, 10 Apr 2026 14:56:47 +0200

For Bassoon and Contrabassoon Tip Profiling Machine

Service Set 12.00 €

Sat, 02 May 2026 00:49:00 +0200

A set of spare parts for the Blade 360° complete with:

1x screw driver tx6
1x screw M2.5

Screw Set 3.12 €

Thu, 30 Apr 2026 13:14:05 +0200

Spare Parts

This set of spare parts for the bassoon tip profiling machine includes:

2 template screws
1 screwdriver TX10

Pen-Oiler 7.19 €

Thu, 30 Apr 2026 13:14:26 +0200

Versatile and reliable

Versatile in use as it neither becomes resinous nor ages. A reliable companion in machinery and tool manufacture, for corrosion protection, and as a cleaner, contact spray, lubricant and rust remover. Well suited for the maintenance and servicing of machine parts, as well the food industry (non-volatile ingredients are approved as additives according to the German Food and Consumer Goods Act).

Advantages

Prevents fine mechanical wear and prolongs the lifespan of chains, moving parts, and bearings
Cleans all machine parts right into the last gap
Lubricates all moving machine parts
Prevents current leakage on electrical components
Loosens rusted and jammed connections
Removes tar marks and protects against fingerprints
Neutralises leaked battery acid or hand perspiration
Cleans resin from planing machines, among other things
Rub it into your hands before starting work and you can easily remove oil and dirt

Environmental Compatibility

Biodegradable. Harmless for humans and nature. Plant friendly. Free from animal products.

Machine Oil 6.13 €

Thu, 30 Apr 2026 13:15:51 +0200

Squeaky clean

The classic multifunctional oil. Dissolves and protects against renewed corrosion.

Eliminates squeaking and creaking noises.

Cleans, preserves and lubricates permanently.

Suitable as a contact spray and displaces moisture.

Precision instrument oil, free of resin and acids.

With hanging tag.

Sealed with a leak proof sealing cap.

Provides precise dosage.

Swab 7.00 €

Wed, 29 Apr 2026 19:18:27 +0200

This highend cleaning fibre is particular carefully, fluffy free and offers highest absorption. It is ideal for cleaning precision mechanics and flaps.